LDL Precision Products

7” PCD THREADED
7” PCD NON-THREADED

BEST FOR AGGRESSIVE REMOVAL OF THICK MIL COATINGS, HEAVY THIN SET AND OVERLAYS

7″ PCD WITH WEAR BAR

BEST FOR AGGRESSIVE REMOVAL OF THICK MIL COATINGS, HEAVY THIN SET AND OVERLAYS. WEAR BARS SLOW CUTTING SPEED SLIGHTLY BUT PREVENT DEEP GOUGING. BEST FOR USE IF YOU ARE APPLYING A THIN TO MEDIUM MIL COATING OR POLISHING AFTER THE FLOOR PREP IS COMPLETE.

7″ MASTIC ERADICATOR

BEST FOR REMOVAL OF TACKEY ADHESIVES AND RUBBER MEMBRANES. ALSO IDEAL FOR THE REMOVAL OF PRESSURE SENSITIVE ADHESIVES.

7″ ARROW THREADED
7″ ARROW NON-THREADED

BEST FOR REMOVAL OF THIN TO MEDIUM COATINGS, THIN SET AND ADHESIVES

7″ TURBO

IDEAL FOR USE AS AN AGGRESSIVE CUT FOR PREPPING CONCRETE TO RECEIVE A THICK COATING OR A TERRAZZO FLOOR INSTALL.

7″ S-SEGMENT 16 GRIT

BEST FOR GRINDING UNEVEN OR ROUGH CONCRETE, ALSO GOOD FOR PREP PRIOR TO A COATING APPLICATION

7″ S-SEGMENT 25 GRIT

BEST FOR GRINDING UNEVEN OR ROUGH CONCRETE, ALSO GOOD FOR PREP PRIOR TO A COATING APPLICATION

 7” S-SEGMENT 30/40 GRIT THREADED

 BEST FOR A MEDIUM GRIND ON FAIRLY SMOOTH CONCRETE OR TERRAZZO, OFTEN USED AFTER A 16 OR 25 GRIT S SEGMENT CUP WHEEL

7” S-SEGMENT 60/80 GRIT THREADED

BEST FOR A MEDIUM GRIND ON FAIRLY SMOOTH CONCRETE OR TERRAZZO, OFTEN USED AFTER A 25 OR 40 GRIT S SEGMENT CUP WHEEL

7” S-SEGMENT 120/150 GRIT THREADED

BEST FOR A LIGHT GRIND ON FAIRLY SMOOTH CONCRETE OR TERRAZZO, OFTEN USED AFTER AN 80-GRIT S SEGMENT CUP WHEEL

7″ 18 SEGMENT TURBO

BEST FOR GRINDING SOFT CONCRETE, THE WIDE SEGMENTS ARE LESS LIKELY TO DIG RINGS INTO THE CONCRETE

7″ 12 SEGMENT TURBO THREADED
7″ 12 SEGMENT TURBO NON-THREADED

BEST FOR AGGRESSIVE FIRST CUT ON MEDIUM CONCRETE

7″ L SEGMENT 25 GRIT

BEST FOR AGGRESSIVE GRINDING OF VERY HARD CONCRETE, MADE WITH A VERY SOFT BOND

7″ L SEGMENT 40 GRIT

BEST FOR GRINDING OF VERY HARD CONCRETE, MADE WITH A VERY SOFT BOND, GOOD GRIT TO START WITH ON A POLISHING PROJECT

7″ V SEGMENT CUP WHEEL

BEST FOR USE WHEN REMOVING THIN TO MEDIUM MIL COATINGS AND FOR PREPPING BARE CONCRETE TO RECIEVE A COATING

7″ CRUSHER CUP WHEEL

BEST FOR REMOVAL OF MEDIUM MIL COATINGS, THICK GLUES, THIN SETS AND FLOOR PATCH. LEAVES THE FLOOR WITH A SEMI ROUGH PROFILE

7” 24 SEGMENT TURBO THREADED
7” 24 SEGMENT TURBO NON-THREADED

BEST FOR CUTTING SOFT TO MEDIUM CONCRETE, HAVING 24 SEGMENTS INCREASES THE LIFE OF THE CUP WHEEL ON SOFTER AND MORE ABRAISIVE MATERIALS

 7” TURBO CUP WHEEL 30/40 GRIT COARSE 

IDEAL FOR USE ON SOFTER CONCRETE, REPLACES ELIMINATOR COARSE CUP WHEEL ON SOFT CONCRETE

7” TURBO CUP WHEEL 60/80 GRIT MEDIUM

IDEAL FOR USE ON SOFTER CONCRETE, REPLACES ELIMINATOR MEDIUM CUP WHEEL ON SOFT CONCRETE

7″ TURBO CUP WHEEL 120/150 GRIT FINE

 IDEAL FOR USE AS THE LAST STEP BEFORE RESINS WHEN POLISHING SOFTER CONCRETE